Recalls for 1998 Plymouth Breeze

There are currently 7 recalls for your car.


What Should You Do?

Bring your car to a dealer immediately. Recalls are issued because the defect might make the car unsafe in some way. Your nearby service center can help verify if the repairs can be performed free of charge.

Contact a Service Center

NHTSA Vehicle Safety Recalls


Recall Number: 10E059000

Recall Date: 12/27/2010

Component: SUSPENSION:FRONT:CONTROL ARM:LOWER ARM

Problem Summary: FEDERAL-MOGUL IS RECALLING CERTAIN REPLACEMENT CONTROL ARM ASSEMBLIES, PART NUMBERS K7425, 10945, FA4510X, K7427, 10946, AND FA4611X, SOLD FOR USE ON VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE BALL JOINT ON THE CONTROL ARM ASSEMBLY CAN FAIL CAUSING THE BALL STUD TO WEAR THROUGH THE CONTROL ARM HOUSING RESULTING IN NOISE AND/OR SEPARATION OF THE BALL STUD FROM THE HOUSING.

Consequence: IF THERE IS A SEPARATION OF THE BALL STUD FROM THE HOUSING, THE DRIVER CAN LOOSE STEERING CONTROL, POSSIBLY RESULTING IN A VEHICLE CRASH.

What Owners Should Do: FEDERAL-MOGUL WILL NOTIFY OWNERS OF RECORD AND REPLACE THE AFFECTED CONTROL ARMS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING JANUARY 2011. OWNERS MAY CONTACT FEDERAL-MOGUL AT 1-877-489-6659.

Next Steps: Contact a Service Center Near You

Recall Number: 09E056000

Recall Date: 10/09/2009

Component: SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

Problem Summary: QUALIS AUTOMOTIVE IS RECALLING CERTAIN AFTERMARKET BALL JOINTS SOLD FOR USE ON CERTAIN PASSENGER VEHICLES. THE SOCKET MAY HAVE BEEN EXCESSIVELY HARDENED WHICH COULD CAUSE IT TO CRACK NEAR THE RETAINING RING GROOVE ALLOWING THE BALL STUD TO SEPARATE UNDER IMPACT LOAD. THE SUBJECT BALL JOINTS WERE SOLD AS FOUR PART NUMBERS, D10945, D10946, G10945, AND G10946. THE AFFECTED CONTROL ARMS, D10945 AND D10946, ARE STAMPED WITH THE FOLLOWING DATES ON THE BALL JOINTS: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, AND 116609. THE G10945 AND G10946 ARE THE SAME PART AS THE D10945 AND D10946 RESPECTIVELY. THEY ARE LABELED DIFFERENTLY DEPENDING ON THE AFTERMARKET CUSTOMER.

Consequence: SEPARATION OF THE BALL STUD FROM THE SOCKET OF THE BALL JOINT HOUSING WOULD ALLOW THE CONTROL ARM TO COLLAPSE AND THE WHEEL TO FOLD IN CAUSING LOSS OF STEERING CONTROL, POSSIBLY RESULTING IN A CRASH.

What Owners Should Do: QUALIS AUTOMOTIVE WILL REPLACE THE BALL JOINTS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT OCTOBER 26, 2009.

Next Steps: Contact a Service Center Near You

Recall Number: 09E043000

Recall Date: 07/07/2009

Component: EQUIPMENT

Problem Summary: IMPORT PRODUCTS IS RECALLING 30,351 FUEL FILTERS SOLD TO AND BRANDED BY THE AFFINIA GROUP AS CARQUEST P/N 86523, NAPA P/N 3523, AND WIX P/N 33523 FOR USE AS REPLACEMENT EQUIPMENT ON THE VEHICLES LISTED ABOVE. THESE FILTERS MAY DEVELOP A LEAK IN THE HOSE ASSEMBLY AND/OR CONNECTORS DUE TO IMPROPERLY ADHERED LINE CONNECTORS.

Consequence: THIS CONDITION MAY RESULT IN A VEHICLE FIRE.

What Owners Should Do: THE AFFINIA GROUP WILL NOTIFY OWNERS AND THE FILTERS WILL BE REPLACED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING JULY 2009. OWNERS MAY CONTACT WIX FILTER RETURN CENTER AT 1-704-869-7411 OR IMPORT PRODUCTS AT 1-508-279-8207.

Next Steps: Contact a Service Center Near You

Recall Number: 06E088000

Recall Date: 10/23/2006

Component: FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP

Problem Summary: CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

Consequence: FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.

What Owners Should Do: TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-866-867-3759.

Next Steps: Contact a Service Center Near You

Recall Number: 04V021000

Recall Date: 01/13/2004

Component: POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT

Problem Summary: ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.

Consequence: EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.

What Owners Should Do: DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.

Next Steps: Contact a Service Center Near You

Recall Number: 99V244000

Recall Date: 09/15/1999

Component: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

Problem Summary: VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE RIGHT REAR BRAKE TUBE CAN CONTACT THE EXHAUST SYSTEM CLAMP AND WEAR A HOLE IN IT.

Consequence: DAIMLERCHRYSLER RECALL NO. 843. IF THIS HAPPENS, THE TUBE COULD LEAK, REDUCING THE EFFECTIVENESS OF ONE-HALF OF THE DIAGONALLY SPLIT BRAKING SYSTEM, AND RESULTING IN LONGER STOPPING DISTANCES.

What Owners Should Do: DEALERS WILL INSPECT THE BRAKE TUBES FOR VISIBLE EVIDENCE OF CONTACT WITH THE EXHAUST SYSTEM CLAMP. IF THE TUBE SHOWS EVIDENCE OF CONTACT, IT WILL BE REPLACED. IF NO EVIDENCE OF CONTACT EXISTS, THE TUBE WILL BE FASTENED WITH A CLIP.

Next Steps: Contact a Service Center Near You

Recall Number: 98V183000

Recall Date: 08/06/1998

Component: POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START SWITCH

Problem Summary: VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.

Consequence: IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.

What Owners Should Do: DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.

Next Steps: Contact a Service Center Near You

Certified Service Centers

Certification requires warranty on parts and labor, fair-price* guarantee, certified technicians and high customer satisfaction ratings.

*Fair prices, measured by comparing them to the RepairPal Price Estimator.

Additional terms and conditions apply