Toyota Recalls

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2004-2010 PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2009 SCION XD AND MY 2009-2010 COROLLA, COROLLA MATRIX AND PONTIAC VIBE VEHICLES EQUIPPED WITH 1.8L ENGINE AND ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF ALASKA, COLORADO, IDAHO, ILLINOIS IOWA, KANSAS, MAINE, MICHIGAN, MINNESOTA, MONTANA, NEBRASKA, NEVADA, NEW HAMPSHIRE, NEW YORK, NORTH DAKOTA, SOUTH DAKOTA, VERMONT, WISCONSIN, AND WYOMING. WHEN DRIVING UNDER CERTAIN UNIQUE CONDITIONS IN EXTREMELY LOW AMBIENT TEMPERATURES, THE INTAKE MANIFOLD SUCTION PORT FOR THE BRAKE VACUUM CAN BECOME LOCKED DUE TO THE FREEZING OF CONDENSATION RESULTING FROM POSITIVE CRANKCASE VENTILATION.

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2010 COROLLA VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE AIR BAG LABEL INSTALLED ON THE DRIVER SIDE SUN VISOR CAN SEPARATE FROM THE SURFACE OF THE VISOR.

TOYOTA IS RECALLING 1,281 MODEL YEAR 2006 THROUGH 2009 SIENNA, 2004 LAND CRUISER, AND 2009 LEXUS GX PASSENGER VEHICLES. THE VEHICLE CAPACITY WEIGHT ON THE TIRE AND LOADING INFORMATION LABEL AND THE GVWR ON THE CERTIFICATION LABEL IS INSUFFICIENT FOR CERTAIN VEHICLES. SOME VEHICLES WERE ACCESSORIZED THROUGH VEHICLE PROCESSING CENTERS AND HAD ACCESSORIES INSTALLED THAT CAUSED THE VEHICLE TO EXCEED THE GVWR VALUE. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO 110, "TIRE SELECTION AND RIMS," AND 49 CFR PART 567.

TOYOTA IS RECALLING 1,348 MODEL YEAR 2009 AND 2010 PASSENGER CARS BUILT FROM JUNE 2, 2008 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."

SOUTHEAST TOYOTA IS RECALLING 3,499 STAINLESS STEEL EXHAUST TIPS SOLD BY SOUTHEAST TOYOTA AS AN OPTIONAL ACCESSORY FOR USE ON MY 2008 HIGHLANDER AND HIGHLANDER HYBIRD VEHICLES. DUE TO IMPROPER HEAT TREATMENT DURING THE MANUFACTURING PROCESS, THE ORIGINAL CLAMP USED TO SECURE THE STAINLESS STEEL EXHAUST TIP TO THE EXHAUST PIPE MAY DEVELOP MICROSCOPIC CRACKS. EVENTUALLY THE CRACK MAY EXPAND CAUSING THE CLAMP TO BREAK.

TOYOTA IS RECALLING 39,100 STAINLESS STEEL EXHAUST TIPS SOLD BY TOYOTA AS AN OPTIONAL ACCESSORY FOR USE ON MY 2008 HIGHLANDER AND HIGHLANDER HYBIRD VEHICLES. DUE TO IMPROPER HEAT TREATMENT DURING THE MANUFACTURING PROCESS, THE ORIGINAL CLAMP USED TO SECURE THE TOYOTA STAINLESS STEEL EXHAUST TIP TO THE EXHAUST PIPE MAY DEVELOP MICROSCOPIC CRACKS. EVENTUALLY THE CRACK MAY EXPAND CAUSING THE CLAMP TO BREAK.

TOYOTA IS CONDUCTING A SAFETY IMPROVEMENT CAMPAIGN INVOLVING 196,222 MY 2004-2006 TOYOTA SIENNA VEHICLES EQUIPPED WITH POWER REAR LIFTGATE STRUTS. THE GAS STRUTS USED TO HELP LIFT AND SUPPORT THE REAR POWER LIFTGATE COULD WEAR OUT SOONER THAN EXPECTED. AS THE GAS STRUTS DETERIORATE, THE PERFORMANCE OF THE LIFTGATE WILL BEGIN TO DEGRADE AND THE POWER REAR LIFTGATE WILL OPERATE MORE SLOWLY THAN WHEN THE GAS STRUTS WERE NEW.

TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.

ON CERTAIN 4-WHEEL DRIVE PICKUP TRUCKS, DUE TO THE IMPROPER HEAT TREATMENT OF THE SLIP YOKES THAT HAD BEEN REWORKED DURING THE MANUFACTURING PROCESS, THE HARDNESS OF THE SLIP YOKE MAY BE INSUFFICIENT.